Daco Ex-demonstration & Used Label Converting Equipment.
On occasions we have ex-demonstration machines that are only a few months old and machines that have been part exchanged against a new machine from the Daco Solutions product range.
Daco DSI 330 (13") rotary die cutter
- Unwind
- Maximum unwind diameter: 762mm (30")
- 76mm (3") diameter air shaft
- Merobel electromagnetic particle brake
- Automatic taper tension control
- End of roll function - The user is able to program the roll end diameter – slowdown and/or stop - The system does not use any roll followers or external sensors that can be damaged at roll changes. The diameter is programmed from the touch screen operator interface.
- Web up - the operator can, at the touch of a button on the touch screen operator interface, release the unwind brake to allow for easier webbing up of the machine.
- Splicing Table
- 700mm (27.5") Inspection area prior to web guiding and slitting with adjustable splicing facility and pneumatic interlocked web clamps.
- Stainless steel topped.
- Die Station
- 1 rotary die station.
- 10"-24" die repeats.
- Rotometrics through hardened anvil - 120T - 15" repeat.
- Gearing - 1/8 cp, 20 degree pressure angle.
- Lateral die adjustment
- Fully adjustable driven capstan roller.
- A driven capstan / matrix stripping roller with adjustable tension control ensures reliable matrix
- Matrix / Waste Rewind -609mm (24") diameter.
- 76mm (3") mechanical mandrel for waste rewind.
- Web guide
- BST electronic web guide.
- Ultrasonic sensor – enables guiding of opaque and clear materials.
- Adjustable web guide sensor.
- +/- 12.5mm (1/2") correction.
- Draw Head
- Pneumatically operated silicone nip roller against a driven draw roller.
- The silicone nip roller does not allow labels to attach themselves to it reducing down time.
- Fully adjustable via a regulator and gauge.
- On / off feature to allow for easy webbing up of the machine.
- Interlocked so that the machine can not be started with the nip roller off.
- The draw roller is driven by a 1.5Kw (2 hp) motor to isolate the unwind tension from the rewind.
- Slitting
- 3 rotary scissor slitting knives (shear knife).
- Knife separation - Allows for easy setting of the knife and anvil with the web in place.
- Minimum slit width: 13mm (0.51")
- Lateral knife adjustment: +/- 5mm (0.196")
- Rewind
- 1 Product rewind
- Maximum rewind diameter: 457mm (18")
- 76mm (3") diameter with quick change air shaft
- Automatic taper tension control
- Merobel electromagnetic particle clutch
- Labels in / labels out rewinding
- Programmable web advance system - The web advance delay time is programmable from the touch screen - enables easy attachment of the web to the core when starting a new roll.
- The mandrels are quick change. The mandrel size is selected on the touch screen and is electronically compensated for, so there are no gears to change.
- The rewind is driven by a 1.5Kw (2 hp) motor.
- Count Facility
- Labels
- Linear - metres & feet
- Stop on diameter
- Total count
- Batch count
- Auto calculation of slow down and stop irrelevant of web speed.
- Touch Screen Operator Interface
- Shows machine status - system messages, interlocks not met etc
- Quick and easy job set ups
- Counting options
- Tension settings
- Speed - 250 metres / minute - 820 feet / minute - dependent on material
AB Graphic - Omega SR330 Inspection / slitter rewinder
- Specification
- 330mm (13") web width
- Web guide
- Rotary slitting with lateral knife adjustment
- Web advance
- Missing label detection
Arpeco Tracker - Inspection / Slitter Rewinder
- Specification
- 13" web width
- Fife web guide
- 25mm (1") rewind shaft
- Rotary slitting with lateral knife adjustment
- Web advance
- Hard roll / soft roll
- Labels in / labels out rewinding
- 6 lane missing label detection
- Strobe
- Label count, Length count (feet, inches, metres) butt cut
